IRQL_NOT_LESS_OR_EQUAL

On a CLEAN INSTALL of WInXP from a system that had been running woth
no such error, I get the IRQL_NOT_LESS_OR_EQUAL error on BSOD with the
following STOP.

*** STOP 0x0000000A (0x00000010 0x00000002, 0x00000000, 0x8051AA5B)


There is no 'new hardware', there are no 'new drivers'. Just a clean
reinstall of XP on known good hardware. I have tried everything I
know to get this running. Anyone have advice?

On Thu, 14 Feb 2008 23:17:11 -0800, frogsteaks wrote:

> On a CLEAN INSTALL of WInXP from a system that had been running woth no
> such error, I get the IRQL_NOT_LESS_OR_EQUAL error on BSOD with the
> following STOP.
>
> *** STOP 0x0000000A (0x00000010 0x00000002, 0x00000000, 0x8051AA5B)
>
>
> There is no 'new hardware', there are no 'new drivers'. Just a clean
> reinstall of XP on known good hardware. I have tried everything I know
> to get this running. Anyone have advice?


Using SP3 beta by chance? I was getting this all last week until I axed SP3 on 2 machines.

frogsteaks@yahoo.com wrote:

>On a CLEAN INSTALL of WInXP from a system that had been running woth
>no such error, I get the IRQL_NOT_LESS_OR_EQUAL error on BSOD with the
>following STOP.
>
>*** STOP 0x0000000A (0x00000010 0x00000002, 0x00000000, 0x8051AA5B)
>
>
>There is no 'new hardware', there are no 'new drivers'. Just a clean
>reinstall of XP on known good hardware. I have tried everything I
>know to get this running. Anyone have advice?

Are you absolutely SURE that you've loaded all the correct hardware
drivers after that clean install??

On Feb 15, 4:31*am, Pete Puma <p...@puma.com> wrote:
> On Thu, 14 Feb 2008 23:17:11 -0800, frogsteaks wrote:
> > On a CLEAN INSTALL of WInXP from a system that had been running woth no
> > such error, I get the IRQL_NOT_LESS_OR_EQUAL error on BSOD with the
> > following STOP.
>
> > *** STOP 0x0000000A (0x00000010 0x00000002, 0x00000000, 0x8051AA5B)
>
> > There is no 'new hardware', there are no 'new drivers'. *Just a clean
> > reinstall of XP on known good hardware. *I have tried everything I know
> > to get this running. *Anyone have advice?
>
> Using SP3 beta by chance? I was getting this all last week until I axed SP3 on 2 machines.

SP3? MS has not released SP3 to my knowledge. I am doing a CLEAN
INSTALL off of an ORIGINAL XP Pro CD. No SPs at all involved.

On Feb 15, 3:46*pm, Uncle Grumpy <unclegru...@comcast.net> wrote:
> frogste...@yahoo.com wrote:
> >On a CLEAN INSTALL of WInXP from a system that had been running woth
> >no such error, I get the IRQL_NOT_LESS_OR_EQUAL error on BSOD with the
> >following STOP.
>
> >*** STOP 0x0000000A (0x00000010 0x00000002, 0x00000000, 0x8051AA5B)
>
> >There is no 'new hardware', there are no 'new drivers'. *Just a clean
> >reinstall of XP on known good hardware. *I have tried everything I
> >know to get this running. *Anyone have advice?
>
> Are you absolutely SURE that you've loaded all the correct hardware
> drivers after that clean install??

I cannot even complete the install! I can't get to the point to
install ****. This happens on the initial reboot DURING install. As
the install is processing I get the BSOD and STOP error.

Anyone have additional feedback on this? Just to clarify here is the
situation.

I had an older Asus MB with a 3.4GHz pentium. For outside reasons I
needed to upgrade my MB/CPU. Got a Core 2 Duo 2.66 CPU and an Intel
DP35DP Motherboard along with a single sGB stick of RAM and a new PCIx
video card..

Swapped out the old MB, CPU, RAM, video and all runs fine. Ran that
for 3-4 weeks and eventually needed to do a clean install of XP with
the new hardware.

On reinstall, all goes well until the initial reboot during the
install process. After XP goes into the GUI to complete the install,
I get to the point where it is loading drivers and I get the error
mentioned above.

---
IRQL_NOT_LESS_OR_EQUAL

*** STOP 0x0000000A (0x00000010 0x00000002, 0x00000000, 0x8051AA5B
---


I have added NO new hardware or software. I am at a loss on how to
get XP to perform a clean install. Any advice would be appreciated.
Remember thsi is NOT an upgrade, its NOT adding new HW or SW.


Thanks

I GOT THIS FIGURED OUT! I had to disable the "Core Multiplexing
Technology" option in BIOS during install.

frogsteaks@yahoo.com wrote:
> On Feb 15, 4:31 am, Pete Puma <p...@puma.com> wrote:

>> Using SP3 beta by chance? I was getting this all last week until I
>> axed SP3 on 2 machines.
>
> SP3? MS has not released SP3 to my knowledge.

It is true that MS has not released SP3 yet. However, they have released
beta versions of it.

No, not a beta. MS has released SP3 Release Candidate to the public for
testing by anyone who wishes to.

http://www.microsoft.com/downloads/d...DisplayLang=en

"Daave" <dcwashNOSPAM@myrealboxXYZ.invalid> wrote in message
news:%23VnYaAEcIHA.4712@TK2MSFTNGP04.phx.gbl...
> frogsteaks@yahoo.com wrote:
>> On Feb 15, 4:31 am, Pete Puma <p...@puma.com> wrote:
>
>>> Using SP3 beta by chance? I was getting this all last week until I
>>> axed SP3 on 2 machines.
>>
>> SP3? MS has not released SP3 to my knowledge.
>
> It is true that MS has not released SP3 yet. However, they have released
> beta versions of it.
>
>

"Colin Barnhorst" <c.barnhorst@comcast.net> wrote:

>No, not a beta. MS has released SP3 Release Candidate to the public for
>testing by anyone who wishes t

Anything that is still in "testing" is technically a beta version, IMO