|
|
|
|
| Author |
Message |
Massimo G.
Guest
|
 Posted: Tue May 08, 2007 10:59 pm Post subject: Xerox Workcentre M123 and Windows Vista |
 |
|
Help Help Help... I have download Vista driver for Workcentre M123 from
Xerox Support Center but when I try to print via network the Workcenter
print many fault pages... There are new setting for TCP/IP port?
Many thanks!
Max |
|
| Back to top |
|
 |
|
|
Warren Block
Guest
|
| Posted: Tue May 08, 2007 11:51 pm Post subject: Re: Xerox Workcentre M123 and Windows Vista |
|
|
Massimo G. <maxful@vira.it> wrote:
| Quote: | Help Help Help... I have download Vista driver for Workcentre M123 from
Xerox Support Center but when I try to print via network the Workcenter
print many fault pages... There are new setting for TCP/IP port?
|
What do the fault pages say? For that matter, what does the vendor say?
--
Warren Block * Rapid City, South Dakota * USA |
|
| Back to top |
|
|
Massimo G.
Guest
|
| Posted: Wed May 09, 2007 1:09 am Post subject: Re: Xerox Workcentre M123 and Windows Vista |
|
|
The Workcentre is 2 years old and I live in a small city... i don't have a
vendor!!! 
Fault page is a page with a lot varius number and simbol... the printer
start to print a lot of page and I must switch off the printer for end the
job... I have try to change any option in printe menu... like processor...
Postscript value... but without solution :(
The printer work good with Windows XP!!!
I have sended a mail to Xerox support center and waiting an answer!
Many thank for your answer
Best regards, Max
"Warren Block" <wblock@wonkity.com> ha scritto nel messaggio
news:slrnf41hl6.3m.wblock@speedy.wonkity.com...
| Quote: | Massimo G. <maxful@vira.it> wrote:
Help Help Help... I have download Vista driver for Workcentre M123 from
Xerox Support Center but when I try to print via network the Workcenter
print many fault pages... There are new setting for TCP/IP port?
What do the fault pages say? For that matter, what does the vendor say?
--
Warren Block * Rapid City, South Dakota * USA |
|
|
| Back to top |
|
|
Warren Block
Guest
|
| Posted: Wed May 09, 2007 1:09 am Post subject: Re: Xerox Workcentre M123 and Windows Vista |
|
|
Massimo G. <maxful@vira.it> wrote:
| Quote: | "Warren Block" <wblock@wonkity.com> ha scritto nel messaggio
news:slrnf41hl6.3m.wblock@speedy.wonkity.com...
Massimo G. <maxful@vira.it> wrote:
Help Help Help... I have download Vista driver for Workcentre M123 from
Xerox Support Center but when I try to print via network the Workcenter
print many fault pages... There are new setting for TCP/IP port?
What do the fault pages say? For that matter, what does the vendor say?
The Workcentre is 2 years old and I live in a small city... i don't have a
vendor!!!
Fault page is a page with a lot varius number and simbol... the printer
start to print a lot of page and I must switch off the printer for end the
job... I have try to change any option in printe menu... like processor...
Postscript value... but without solution 
|
[please don't top-post, it makes responding difficult]
Pages with garbled symbols can happen from the printer being interrupted
during a job, or possibly by receiving a job with commands that it
doesn't understand. For example, if the printer only supports PCL 3 but
the new driver sends PCL 5, or the same with PostScript level 2 versus
level 3.
It's unlikely, but worth checking to see if Xerox has a firmware update
for the printer. The Vista driver may require newer firmware.
There may be some networking "feature" of Vista that is interfering with
network communications, like a firewall.
| Quote: | The printer work good with Windows XP!!!
|
A lot of people are experiencing problems with Vista. Many go back to
XP.
| Quote: | I have sended a mail to Xerox support center and waiting an answer!
|
When or if you receive a response, please post it in this thread.
--
Warren Block * Rapid City, South Dakota * USA |
|
| Back to top |
|
|
|
|
| |
Watched Topics
Search
Register
Log in to check your private messages
Profile
Log in
Memberlist
Usergroups