|
|
| Author |
Message |
Eustace
Guest
|
 Posted: Thu Nov 27, 2003 12:53 pm Post subject: Tabor II & III 4W4SBOXO Motherboards |
 |
|
I replaced board #4000402 running PIII 1000MHZ 512megs for about two years
with board #4000472.
The motherboard functioned as expected through the boot post utill it was
about to enter Windows XP. At that point I got error message " system
32\Driver\pci.sys missing or corrupt". and the computer hangs.
When I try to boot from the Windows Setup Disk I alternatively get the
following messages:
"The file pci.sys is corrupted"
"File setupdd.sys could not be loaded error code 4"
"File ntkrnlmp.exe could not be loaded, error code 7"
"Setup is loading files (kernell Debugger.dll)" The computer hangs.
I would appreciate any help the group can give.
Thanks
Eustace |
|
| Back to top |
|
 |
|
|
PC Gladiator
Guest
|
| Posted: Thu Nov 27, 2003 12:53 pm Post subject: Re: Tabor II & III 4W4SBOXO Motherboards |
|
|
Check this out and see if it helps...
http://www.theeldergeek.com/replace_motherboard.htm
"Eustace" <joelee@caribsurf.com> wrote in message
news:vsb4ap3eurnv25@corp.supernews.com...
| Quote: | I replaced board #4000402 running PIII 1000MHZ 512megs for about two years
with board #4000472.
The motherboard functioned as expected through the boot post utill it was
about to enter Windows XP. At that point I got error message " system
32\Driver\pci.sys missing or corrupt". and the computer hangs.
When I try to boot from the Windows Setup Disk I alternatively get the
following messages:
"The file pci.sys is corrupted"
"File setupdd.sys could not be loaded error code 4"
"File ntkrnlmp.exe could not be loaded, error code 7"
"Setup is loading files (kernell Debugger.dll)" The computer hangs.
I would appreciate any help the group can give.
Thanks
Eustace
|
|
|
| Back to top |
|
|
Edward J. Neth
Guest
|
| Posted: Thu Nov 27, 2003 6:06 pm Post subject: Re: Tabor II & III 4W4SBOXO Motherboards |
|
|
Not all these boards will support a 1 GHz CPU - it sounds like despite the
higher part number, the replacement board is an older revision that won't
support a Coppermine processor (i.e., you can use only Katmai processors up
to a 600 MHz PIII).
"Eustace" <joelee@caribsurf.com> wrote in message
news:vsb4ap3eurnv25@corp.supernews.com...
| Quote: | I replaced board #4000402 running PIII 1000MHZ 512megs for about two years
with board #4000472.
The motherboard functioned as expected through the boot post utill it was
about to enter Windows XP. At that point I got error message " system
32\Driver\pci.sys missing or corrupt". and the computer hangs.
When I try to boot from the Windows Setup Disk I alternatively get the
following messages:
"The file pci.sys is corrupted"
"File setupdd.sys could not be loaded error code 4"
"File ntkrnlmp.exe could not be loaded, error code 7"
"Setup is loading files (kernell Debugger.dll)" The computer hangs.
I would appreciate any help the group can give.
Thanks
Eustace
|
|
|
| Back to top |
|
|
Eustace
Guest
|
| Posted: Thu Nov 27, 2003 9:30 pm Post subject: Re: Tabor II & III 4W4SBOXO Motherboards |
|
|
The CPU the memory showed up OK both in the post at boot up and in the BIOS
it is only as it boots into the operating system that I get these problems.
Thanks for your comment nonetheless.
"Edward J. Neth" <ejn63@netscape.com> wrote in message
news:PMlxb.34369$hz2.27959@newssvr31.news.prodigy.com...
| Quote: | Not all these boards will support a 1 GHz CPU - it sounds like despite the
higher part number, the replacement board is an older revision that won't
support a Coppermine processor (i.e., you can use only Katmai processors
up
to a 600 MHz PIII).
"Eustace" <joelee@caribsurf.com> wrote in message
news:vsb4ap3eurnv25@corp.supernews.com...
I replaced board #4000402 running PIII 1000MHZ 512megs for about two
years
with board #4000472.
The motherboard functioned as expected through the boot post utill it
was
about to enter Windows XP. At that point I got error message " system
32\Driver\pci.sys missing or corrupt". and the computer hangs.
When I try to boot from the Windows Setup Disk I alternatively get the
following messages:
"The file pci.sys is corrupted"
"File setupdd.sys could not be loaded error code 4"
"File ntkrnlmp.exe could not be loaded, error code 7"
"Setup is loading files (kernell Debugger.dll)" The computer hangs.
I would appreciate any help the group can give.
Thanks
Eustace
|
|
|
| Back to top |
|
|
Edward J. Neth
Guest
|
| Posted: Thu Nov 27, 2003 11:56 pm Post subject: Re: Tabor II & III 4W4SBOXO Motherboards |
|
|
You can try reinstalling XP, but if this is a board that doesn't support
Coppermine processors, what you're seeing could be a direct result. The
Coppermine CPUs have a set of instructions that the OS may attempt to use,
but which won't work properly if the BIOS doesn't support them.
"Eustace" <joelee@caribsurf.com> wrote in message
news:vsc2jm1q6gio6b@corp.supernews.com...
| Quote: | The CPU the memory showed up OK both in the post at boot up and in the
BIOS
it is only as it boots into the operating system that I get these
problems.
Thanks for your comment nonetheless. |
|
|
| Back to top |
|
|
Fix your Windows Problems - FAST.
FREE Safe Scan Registry Check. Locate & Fix Errors in Minutes!
|
|
|
Watched Topics
Search
Register
Log in to check your private messages
Profile
Log in
Memberlist
Usergroups