|
|
|
|
| Author |
Message |
farmuse
Guest
|
 Posted: Wed Jul 27, 2005 3:32 am Post subject: long live the 503+ |
 |
|
Just finished building a computer based on the VA-503+ version 1.2a
from several defunct or unused systems. The CPU was a K6 2 450, which I
changed to a K6 III+ 450 once I noticed the BIOS was JE4333 APM and
could run that CPU. I then added 2x 128 MB Crucial PC133 CAS 2 modules,
a Promise Ultra 66 controller card, a Maxtor 7 GB drive, AWE 64 gold,
NIC, and a still respectable Diamond S220 PCI graphics card. I didn't
have any really good AGP cards that would have been good choices, but I
may look for Rage Fury Pro later. I then enabled USB, loaded Windows 98
SE, and then followed the suggested guidelines from an old friend from
this newsgroup, Jim Navas, and also some from Bill Lahr. Mt first
attempt was crap, I had forgot some of the tweaks you need to do to get
this board running well, but then recalled I had some articles from 1998
that Jim, Bill, and others had written and they helped a lot. Still not
sure why USB has to be enabled, but it did make a difference. I run the
double sided SDRAM at 100 MHz, CAS 2, fast speed, 4 bank interleave. The
other tweak that made a difference was to disable write cache pipeline,
because I was getting lockups when I defragmented the drive. Once write
cache pipeline was disabled the L2 cache was fine, and the system could
properly defragment. Overall the speed is VERY good. I also modded a
dual USB cable set to work with the board, most are set up wrong for
this particular board. I may also add another drive and dual boot to XP
pro as some have said the 503+ runs XP just fine. I have run XP home
with a 503A, no problems, so this should work too.
I guess I just wanted to prove a 503+ could still get the job
done, and would serve most users needs just fine. Not bad for a six year
old motherboard ! Long live the 503+ !
Cheers, John |
|
| Back to top |
|
 |
|
|
Roger Hunt
Guest
|
| Posted: Thu Jul 28, 2005 12:39 am Post subject: Re: long live the 503+ |
|
|
On Wed, 27 Jul 2005, farmuse typed this :
| Quote: | Just finished building a computer based on the VA-503+ version 1.2a
from several defunct or unused systems. The CPU was a K6 2 450, which I
changed to a K6 III+ 450 once I noticed the BIOS was JE4333 APM and
could run that CPU. I then added 2x 128 MB Crucial PC133 CAS 2 modules,
a Promise Ultra 66 controller card, a Maxtor 7 GB drive, AWE 64 gold,
NIC, and a still respectable Diamond S220 PCI graphics card. I didn't
have any really good AGP cards that would have been good choices, but I
may look for Rage Fury Pro later.
|
A Hercules 3D Prophet 4500 64MB goes well.
| Quote: | I then enabled USB, loaded Windows 98
SE, and then followed the suggested guidelines from an old friend from
this newsgroup, Jim Navas, and also some from Bill Lahr. Mt first
attempt was crap, I had forgot some of the tweaks you need to do to get
this board running well, but then recalled I had some articles from 1998
that Jim, Bill, and others had written and they helped a lot. Still not
sure why USB has to be enabled, but it did make a difference. I run the
double sided SDRAM at 100 MHz, CAS 2, fast speed, 4 bank interleave. The
other tweak that made a difference was to disable write cache pipeline,
because I was getting lockups when I defragmented the drive. Once write
cache pipeline was disabled the L2 cache was fine, and the system could
properly defragment. Overall the speed is VERY good. I also modded a
dual USB cable set to work with the board, most are set up wrong for
this particular board. I may also add another drive and dual boot to XP
pro as some have said the 503+ runs XP just fine. I have run XP home
with a 503A, no problems, so this should work too.
It does, perfectly usable - I ran XP pro for a time on mine, shortly |
before the Terrible Disaster.
| Quote: | I guess I just wanted to prove a 503+ could still get the job
done, and would serve most users needs just fine. Not bad for a six year
old motherboard ! Long live the 503+ !
It will never die! I can see it in years to come - the post applauding |
the performance of the twenty-five year old 503+
--
Roger Hunt |
|
| Back to top |
|
|
farmuse
Guest
|
| Posted: Thu Jul 28, 2005 9:12 pm Post subject: Re: long live the 503+ |
|
|
Roger,
what happened ? sounds bad, you don't live in London do you ?
is that 4500 a Kryo chipset ? like it ? what version of Direct x is
that card ? really the S220 is not bad for 2D, I am running 1024x 768 24
bit and it is very sharp and fast. If you recall it uses a Rendition
V2100 chipset and has 4 MB of fast SGRAM, in it's day the 3D was almost
as good as 3Dfx. This computer won't be used for games much, more soho
type stuff. |
|
| Back to top |
|
|
Roger Hunt
Guest
|
| Posted: Thu Jul 28, 2005 9:37 pm Post subject: Re: long live the 503+ |
|
|
On Thu, 28 Jul 2005, farmuse typed this :
| Quote: | Roger,
what happened ? sounds bad, you don't live in London do you ?
The Great Disaster? No, not terrorists but a melt-down of my 503+. |
(Used to live in London and was bombed in 1981 anyway!)
| Quote: | is that 4500 a Kryo chipset ? like it ? what version of Direct x is
that card ?
|
It's a KyroII chipset and if I recall, from a couple of years ago, I
think it was a DX7 card, but ran OpenGL quite nicely.
| Quote: | really the S220 is not bad for 2D, I am running 1024x 768 24
bit and it is very sharp and fast. If you recall it uses a Rendition
V2100 chipset and has 4 MB of fast SGRAM, in it's day the 3D was almost
as good as 3Dfx. This computer won't be used for games much, more soho
type stuff.
|
I've no experience of the S220 but it sounds pretty reasonable ... maybe
keep it?
I must go Googling ... either another 503+, or a PA-2013 would fit this
spare case well. Have all the internals already, and a K6-2+/533 CPU
sitting in a draw doing nothing.
Cheers!
--
Roger Hunt |
|
| Back to top |
|
|
farmuse
Guest
|
| Posted: Tue Aug 02, 2005 12:52 am Post subject: Re: long live the 503+ |
|
|
sounds like a good plan Roger, put that cpu to use ! hey, the only
glitch with this set up is the video goes to scrambled screen when
windows powers down, wonder why ? like the refresh rate is not what the
monitor likes. very strange, the monitor is multi-sync for sure, maybe a
driver issue. these are the drivers that came with the card. the video
BIOS is cached, I don't believe the 503+ is the issue. anyone have any
ideas ?
Roger Hunt wrote:
| Quote: | On Thu, 28 Jul 2005, farmuse typed this :
Roger,
what happened ? sounds bad, you don't live in London do you ?
The Great Disaster? No, not terrorists but a melt-down of my 503+.
(Used to live in London and was bombed in 1981 anyway!)
is that 4500 a Kryo chipset ? like it ? what version of Direct x is
that card ?
It's a KyroII chipset and if I recall, from a couple of years ago, I
think it was a DX7 card, but ran OpenGL quite nicely.
really the S220 is not bad for 2D, I am running 1024x 768 24
bit and it is very sharp and fast. If you recall it uses a Rendition
V2100 chipset and has 4 MB of fast SGRAM, in it's day the 3D was almost
as good as 3Dfx. This computer won't be used for games much, more soho
type stuff.
I've no experience of the S220 but it sounds pretty reasonable ... maybe
keep it?
I must go Googling ... either another 503+, or a PA-2013 would fit this
spare case well. Have all the internals already, and a K6-2+/533 CPU
sitting in a draw doing nothing.
Cheers! |
|
|
| Back to top |
|
|
|
|
Alex Zorrilla
Guest
|
| Posted: Tue Aug 02, 2005 8:34 pm Post subject: Re: long live the 503+ |
|
|
To my knowledge, the last set of reference drivers for the Rendition
V2000/V2100 can be found here:
http://www.micron.com/support/itg/v2x00.html
Rendition was taken over by Micron a long time ago. They are beta
drivers (version 3 beta 5), but something tells me you are not going to
find an official release anytime soon. ;)
You may also try the reconstituted Diamond Multimedia at
http://www.diamondmm.com for drivers. They are probably older than the
ones on the Micron site, but they may be newer than the ones that came
with the card.
For whatever it is worth, we have a Geforce 4 MX 420 AGP card running
just fine on a VA-503A. It has very good DVD playback, even with a
K6-III 350 (which has since been upgraded to K6-III+ 400 overclocked to
550).
--Alex
farmuse wrote:
| Quote: | sounds like a good plan Roger, put that cpu to use ! hey, the only
glitch with this set up is the video goes to scrambled screen when
windows powers down, wonder why ? like the refresh rate is not what the
monitor likes. very strange, the monitor is multi-sync for sure, maybe a
driver issue. these are the drivers that came with the card. the video
BIOS is cached, I don't believe the 503+ is the issue. anyone have any
ideas ?
Roger Hunt wrote:
On Thu, 28 Jul 2005, farmuse typed this :
Roger,
what happened ? sounds bad, you don't live in London do you ?
The Great Disaster? No, not terrorists but a melt-down of my 503+.
(Used to live in London and was bombed in 1981 anyway!)
is that 4500 a Kryo chipset ? like it ? what version of Direct x is
that card ?
It's a KyroII chipset and if I recall, from a couple of years ago, I
think it was a DX7 card, but ran OpenGL quite nicely.
really the S220 is not bad for 2D, I am running 1024x 768 24 bit and
it is very sharp and fast. If you recall it uses a Rendition V2100
chipset and has 4 MB of fast SGRAM, in it's day the 3D was almost as
good as 3Dfx. This computer won't be used for games much, more soho
type stuff.
I've no experience of the S220 but it sounds pretty reasonable ... maybe
keep it?
I must go Googling ... either another 503+, or a PA-2013 would fit this
spare case well. Have all the internals already, and a K6-2+/533 CPU
sitting in a draw doing nothing.
Cheers! |
|
|
| Back to top |
|
|
farmuse
Guest
|
| Posted: Tue Aug 02, 2005 8:34 pm Post subject: Re: long live the 503+ |
|
|
thank you very much Alex, I had no idea Micron bought them out. I
was wondering what happened to them !
really it is a very good 2D card for what it is, and I will let
you know how the newer driver works out. I am working on another K6 III
and 503+ project, but the IRQ steering got corrupt, so I flashed the
BIOS to JE439 and will try again. this one is for the mother-in-law who
uses the computer for e mail and IM stuff. maybe store some images and
back them up to CD. should do fine.
thanks again, John
Alex Zorrilla wrote:
| Quote: | To my knowledge, the last set of reference drivers for the Rendition
V2000/V2100 can be found here:
http://www.micron.com/support/itg/v2x00.html
Rendition was taken over by Micron a long time ago. They are beta
drivers (version 3 beta 5), but something tells me you are not going to
find an official release anytime soon. ;)
You may also try the reconstituted Diamond Multimedia at
http://www.diamondmm.com for drivers. They are probably older than the
ones on the Micron site, but they may be newer than the ones that came
with the card.
For whatever it is worth, we have a Geforce 4 MX 420 AGP card running
just fine on a VA-503A. It has very good DVD playback, even with a
K6-III 350 (which has since been upgraded to K6-III+ 400 overclocked to
550).
--Alex
farmuse wrote:
sounds like a good plan Roger, put that cpu to use ! hey, the
only glitch with this set up is the video goes to scrambled screen
when windows powers down, wonder why ? like the refresh rate is not
what the monitor likes. very strange, the monitor is multi-sync for
sure, maybe a driver issue. these are the drivers that came with the
card. the video BIOS is cached, I don't believe the 503+ is the issue.
anyone have any ideas ?
Roger Hunt wrote:
On Thu, 28 Jul 2005, farmuse typed this :
Roger,
what happened ? sounds bad, you don't live in London do you ?
The Great Disaster? No, not terrorists but a melt-down of my 503+.
(Used to live in London and was bombed in 1981 anyway!)
is that 4500 a Kryo chipset ? like it ? what version of Direct x is
that card ?
It's a KyroII chipset and if I recall, from a couple of years ago, I
think it was a DX7 card, but ran OpenGL quite nicely.
really the S220 is not bad for 2D, I am running 1024x 768 24 bit and
it is very sharp and fast. If you recall it uses a Rendition V2100
chipset and has 4 MB of fast SGRAM, in it's day the 3D was almost as
good as 3Dfx. This computer won't be used for games much, more soho
type stuff.
I've no experience of the S220 but it sounds pretty reasonable ... maybe
keep it?
I must go Googling ... either another 503+, or a PA-2013 would fit this
spare case well. Have all the internals already, and a K6-2+/533 CPU
sitting in a draw doing nothing.
Cheers! |
|
|
| Back to top |
|
|
farmuse
Guest
|
| Posted: Mon Aug 08, 2005 1:33 pm Post subject: Re: long live the 503+ |
|
|
Thanks Alex, worked like a charm. Now the computer does not have a
garbled screen on power off, and it displays the correct message in 98.
Runs great, and I just about finished the second 503+ system for my
mother-in-law. I know I am taking a risk, it had best work right !
I could have gone the safe route with an more modern setup, but I like
making something out of nothing, and so far I have almost $18 invested,
and it comes with a nice 17 inch screen and a CD RW too, a good one.
That one does not display the 98 message saying it is now safe to shut
off your computer, so I have to troubleshoot that, but other than that
and the not so hot FX-3D ISA sound card, it runs great. Thanks again for
the help Alex.
cheers, John |
|
| Back to top |
|
|
Roger Hunt
Guest
|
| Posted: Mon Aug 08, 2005 5:33 pm Post subject: Re: long live the 503+ |
|
|
On Mon, 8 Aug 2005, farmuse typed this :
| Quote: | Thanks Alex, worked like a charm. Now the computer does not have a
garbled screen on power off, and it displays the correct message in 98.
Runs great, and I just about finished the second 503+ system for my
mother-in-law. I know I am taking a risk, it had best work right !
I could have gone the safe route with an more modern setup, but I like
making something out of nothing, and so far I have almost $18 invested,
and it comes with a nice 17 inch screen and a CD RW too, a good one.
That one does not display the 98 message saying it is now safe to shut
off your computer, so I have to troubleshoot that, but other than that
and the not so hot FX-3D ISA sound card, it runs great. Thanks again for
the help Alex.
The "It is safe to ..." message lives in the file ..\windows\logos.sys |
The "Windows is shutting down" message is ..\windows\logow.sys
They are in fact 320w x 400h 256 colour bitmaps and the dimensions are
correct, despite looking odd in mspaint.
--
Roger Hunt |
|
| Back to top |
|
|
Stanley Chu
Guest
|
| Posted: Thu Aug 11, 2005 12:33 pm Post subject: Re: long live the 503+ |
|
|
I have 3 desktop and 1 notebook computers at home. The one built with
VA-503+ is the most stable and it rarely crashes.
"farmuse" <spammenot@farms.net> ???
news:eVCFe.9718$oZ.3982@newsread2.news.atl.earthlink.net ???...
| Quote: | Just finished building a computer based on the VA-503+ version 1.2a
from several defunct or unused systems. The CPU was a K6 2 450, which I
changed to a K6 III+ 450 once I noticed the BIOS was JE4333 APM and
could run that CPU. I then added 2x 128 MB Crucial PC133 CAS 2 modules,
a Promise Ultra 66 controller card, a Maxtor 7 GB drive, AWE 64 gold,
NIC, and a still respectable Diamond S220 PCI graphics card. I didn't
have any really good AGP cards that would have been good choices, but I
may look for Rage Fury Pro later. I then enabled USB, loaded Windows 98
SE, and then followed the suggested guidelines from an old friend from
this newsgroup, Jim Navas, and also some from Bill Lahr. Mt first
attempt was crap, I had forgot some of the tweaks you need to do to get
this board running well, but then recalled I had some articles from 1998
that Jim, Bill, and others had written and they helped a lot. Still not
sure why USB has to be enabled, but it did make a difference. I run the
double sided SDRAM at 100 MHz, CAS 2, fast speed, 4 bank interleave. The
other tweak that made a difference was to disable write cache pipeline,
because I was getting lockups when I defragmented the drive. Once write
cache pipeline was disabled the L2 cache was fine, and the system could
properly defragment. Overall the speed is VERY good. I also modded a
dual USB cable set to work with the board, most are set up wrong for
this particular board. I may also add another drive and dual boot to XP
pro as some have said the 503+ runs XP just fine. I have run XP home
with a 503A, no problems, so this should work too.
I guess I just wanted to prove a 503+ could still get the job
done, and would serve most users needs just fine. Not bad for a six year
old motherboard ! Long live the 503+ !
Cheers, John |
|
|
| Back to top |
|
|
|
|
|
  |
Index
-> Fic |
All times are GMT
|
| Page 1 of 1 |
|
| |
Watched Topics
Search
Register
Log in to check your private messages
Profile
Log in
Memberlist
Usergroups